This SPAD.neXt profile is designed for Logitech/Saitek panels, including multi, switch, and radio panels, to make them compatible with the DC Designs Concorde. If you come across any bugs, mistakes, or have suggestions, please don't hesitate to reach out to me!
I recommend using a lower multi panel tuner pollrate. You can change it in settings > devices > multipanel (image)
Lower values will give you a smoother experience.
Installation:
Put "Concorde Logitech Panels (current version) by Pollot.xml" into your SPAD.neXt profiles folder.
[Default location: C:\Users\[your name]\Documents\SPAD.neXt\profiles]
Description of profile functions (also located in the .zip file):
Concorde Logitech Panels SPAD.neXt Profile - version 1.0 / created by Pollot (don't copy my work without my permission)
/////////////////////////////////////////////////////////
Switch Panel:
Master Battery [BAT] - Turns batteries ON/OFF
Master Alternator [ALT] - Turns ground service power CLOSE(ON)/OFF
Avionics Master - Changes RAD/INS switch position
Fuel Pump - Turns all master circuit breakers (feel/stab switches) ON/OFF
De-Ice - Turns engine anti-icing for all engines ON/OFF
Pitot Heat - Turns both pitot heaters ON/OFF
Close Cowl - Turns engines reheats (afterburners) ON/OFF
Panel Lights - Turns panel lights test ON/OFF (I wasn't able to bind panel lightning correctly)
Beacon Lights - Turns beacon lights ON/OFF
Navigation Lights [NAV] - Turns navigation lights ON/OFF
Strobe Lights - Turns strobe (anti-collision) lights ON/OFF
Taxi Lights - Turns taxi Lights (including turn-off lights) ON/OFF
Landing Lights - Turns all landing lights ON/OFF
Magneto OFF - does nothing
Magneto R - Nr. 3 engine starter ON
Magneto L - Nr. 2 engine starter ON
Magneto BOTH/ALL - Nr. 4 engine starter ON
Magneto START - Nr. 3 engine starter ON
Gear Lights:
Green - Fully extended
Yellow - Fully extended, but with airspeed equal to, or greater than 250 knots
Red - Not fully extended
Off - Retracted
Landing Gear Lever - Controls landing gear lever position
/////////////////////////////////////////////////////////
Multi Panel: function after "//" is activated when you press and hold a button for longer than one second
Alt tab:
- Displays selected altitude and selected vertical speed
- Knob changes selected altitude by 100ft / 1000ft
VS tab:
- Displays selected altitude and selected vertical speed
- Knob changes selected vertical speed by 80ft / 480ft
IAS tab:
- Displays selected autothrottle speed
- Knob changes selected speed by 1kt / 10kt
HDG tab:
- Displays selected heading
- Knob changes selected heading by 1° / 10°
COURSE tab:
- Displays selected course (NAV1)
- Knob changes selected course by 1° / 10° (NAV1)
Autopilot [AP] - Turns autopilot ON/OFF
Heading [HDG] - Turns heading hold mode ON/OFF
Navigation [NAV] - Turns Inertial Navigation System mode [INS] ON/OFF
Indicated Airspeed [IAS] - Turns airspeed hold mode ON/OFF // Turns IAS ACQ mode ON/OFF
Altitude [ALT] - Turns altitude hold mode ON/OFF // Turns ALT ACQ mode ON/OFF
Vertical Speed [VS] - Turns vertical speed mode ON/OFF
Approach [APR] - Turns approach (glide) mode ON/OFF
!Reverse Course [REV] - Makes altitude/speed/degrees increments bigger and enables faster frequency changes on radio panel
Auto Throttle - Turns auto throttle 1 ON/OFF
Flaps UP - Visor up by a 1 notch // Visor full up
Flaps DN - Visor down by a 1 notch // Visor full down
Pitch Trim - Changes selected vertical speed
/////////////////////////////////////////////////////////
Radio Panel:
The inner knob changes COM1/2 frequency by 0.005 MHz and the outer by 1 MHz
The inner knob changes ADF1/2 frequency by 1 MHz and the outer by 10 MHz
With REV ON inner knob changes COM1/2 frequency by 0.05 MHz and the outer still by 1 MHz
With REV ON inner knob changes ADF1/2 frequency by 10 MHz and the outer by 100 Mhz
ADF changes active ADF, not standby
DME shows a distance from NAV1 on the left side and the NAV2 on the right side
In the XPDR tab, you can change your QNH using the outer knob, and squawk using the inner (press transfer button to change between squawk numbers)
Holding the transfer button in the XPDR tab for longer than one second will set QNH to a standard value
/////////////////////////////////////////////////////////
That's all, fly safe!
Great work, I'll give it a try.
2 years ago
fgrooten
Thank you!
2 years ago
Vizipok